Ampatop ProtectaStripe
Roof valley membrane
Triple layer, highly tear-resistant roof valley membrane.
- Monolithic technology
- Resistant to driving rain and wind-proof
Triple layer, highly tear-resistant roof valley membrane. Monolithic technology.
Article number | Description | Roll dimensions |
|---|---|---|
| 7640115538871 | Ampatop ProtectaStripe | 0,5 m × 50 m = 25 m2 |
| Property | Value | Standard |
|---|---|---|
| Harmonised European Standard | EN 13859-1:2014 | |
|
Mass per unit area |
190 g/m2 |
EN 1849-2 |
|
Straightness |
< 75 mm/10 m |
EN 1848-2 |
|
Fire behaviour |
E | EN 13 501-1 / EN ISO 11925-2 |
|
Resistance to water penetration |
W1 | EN 1928 |
|
Water vapour permeability, sD value |
0,1 m | EN 1931 |
|
Width of overlap |
10 cm | |
|
Temperature resistance |
-40 to +80 °C | |
|
Maximum tensile strength longitudinal / transverse |
360 / 270 N/5 cm |
EN 12 311-2, without support liner EN 13 859-1, Appendix A, with support liner |
|
Elongation longitudinal / transverse |
60 / 75 % |
EN 12 311-2, without support liner EN 13 859-1, Appendix A, with support liner |
|
Resistance to tearing (nail) longitudinal / transverse |
220 / 240 N |
EN 12 310-1 without support liner EN 13 859-1, Appendix B, with support liner |
|
Dimensional Stability |
-2 % |
EN 1107-2 |
|
Cold bending behaviour (flexibility) |
-40 °C | |
|
Resistance to air penetration (a value) |
< 0,004 m3/m2 x h x 50 Pa |
|
| approved | Driving rain test TU Berlin | |
|
Outdoor weathering |
3 months | |
|
Minimum roof slope |
10° | |
| Visible defects | none | EN 1850-2 |
| Values after artificial ageing | ||
|
Maximum tensile strength longitudinal / transverse |
345 / 242 N/5 cm |
EN 13859-1, appendix C, EN 1297, EN 1296 |
|
Elongation longitudinal / transverse |
345 / 242 N/5 cm |
EN 13859-1, appendix C, EN 1297, EN 1296 |
|
Resistance to water penetration |
W1 | EN 13859-1, appendix C, EN 1297, EN 1296 |
Technical data sheets
|
Technical data sheet: Ampatop ProtectaStripe | Technical data sheet: Ampatop ProtectaStripe, roof valley membrane |
Declarations of performance
|
|
Declaration of perfomance: Ampatop ProtectaStripe | Declaration of perfomance: Ampatop ProtectaStripe 0,5 x 50m, roof valley membrane |
Product inserts
|
|
Product insert: Ampatop ProtectaStripe | Product insert: Ampatop ProtectaStripe 0,5 x 50m, Roof valley membrane |
Product photos
|
Product photo: Ampatop ProtectaStripe | Product photo: Ampatop ProtectaStripe, roof valley membrane |
Ampatop ProtectaStripe should be laid onto the existing support structure or shell, parallel to the eaves, with an overlap of 10 cm. It should then be nailed (with broadheaded nails) or stapled in the overlapping section, with the overlap covering the nails or staples. Tape the overlaps down with the adhesive tape Ampacoll Flexx to make them rain-proof and windproof. Rub the adhesive locations in well. Transverse joints should also overlap by 10 cm. These should be taped with Ampacoll Superfix or Ampacoll Flexx. Fix cross battens with Ampacoll ND nail seals or Ampacoll ND.Band / ND Duo nail seal tape. Connections to gutter beds and the edges of chimneys, dormer windows and other built-in fitments must be permanently glued with Ampacoll Superfix and mechanically secured. Penetration points such as ventilation shafts, ventilation flues, etc must be sealed with Ampacoll BK 535 butyl rubber tape. Porous, dusty or fleecy sub-surfaces must be pretreated with Ampacoll Primax or Ampacoll Airmax before applying Ampacoll BK butyl tapes.
